Drilling, Cutting, Pneumatic & Installation Tool Sourcing

M35 cobalt HSS twist drills

Ground twist drills combine a round shank, spiral chip flutes and a cobalt HSS material direction. Select the work material and actual drilling setup before trial.

Dimensions and configurations

23 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Pieces/box

Configuration	Diameter mm	Working length mm	Overall length mm	Pieces/box
1	1	12	34	10
2	1.5	18	40	10
3	2	24	49	10
4	2.5	30	57	10
5	3	33	61	10
6	4	43	75	10
7	4.2	43	75	10
8	5	51	85	10
9	5.2	52	86	10
10	5.5	57	93	10
11	6	57	93	10
12	7.5	69	109	10
13	8	75	117	5
14	8.5	75	117	5
15	9	81	125	5
16	9.5	81	125	5
17	10	87	133	5
18	10.5	87	133	5
19	11	94	142	5
20	11.5	94	142	5
21	12	101	151	5
22	12.5	101	151	5
23	13	101	151	5

Carbide-tip circular blades for metal sheet

Carbide-tip teeth and edge protection support selected thin steel and corrugated-sheet cutting configurations. Match the marked blade, machine and workpiece.

Dimensions and configurations

6 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Teeth | Bore mm

Configuration	Outside diameter mm	Tooth width mm	Teeth	Bore mm
1	105	1.5	32	20
2	254	3	120	25.4
3	110	1.4	24	20
4	130	1.6	30	20
5	185	1.9	36	20
6	355	2.4	72	25.4

Application reference

Selected thin steel sheet below 3 mm; confirm the exact blade and operating limits

Square-shank U-flute hammer drills

A 40Cr body, YG8 carbide tip and U-flute construction pair with the specified four-pit square interface. This direction excludes steel-containing or reinforced walls.

Dimensions and configurations

23 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm

Configuration	Diameter mm	Working length mm	Overall length mm
1	6	45	110
2	6	75	140
3	8	90	150
4	10	50	110
5	10	90	150
6	12	90	150
7	14	90	150
8	16	90	150
9	10	140	200
10	12	140	200
11	14	140	200
12	16	140	200
13	18	140	200
14	20	140	200
15	22	180	250
16	25	180	250
17	12	280	340
18	14	280	340
19	16	280	340
20	18	280	340
21	20	280	340
22	22	280	340
23	25	280	340

Carbide-tip pointed and flat chisels

40Cr and YG8 construction combines pointed or flat edges with square or hexagonal attachment directions. Confirm the holder drawing and selected edge.

Square pointed

10×130; 12×150 mm

Square flat

10×130; 12×150 mm

Hexagonal pointed or flat

17×230 mm

Square flat, wider illustrated direction

14×130 mm; approve holder and actual geometry

Round-shank U-flute hammer drills

A 40Cr body and YG8 carbide tip combine with a U flute and a round hammer-drill interface. Keep working length and overall length paired.

Dimensions and configurations

38 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm

Configuration	Diameter mm	Working length mm	Overall length mm
1	6	45	110
2	6	75	140
3	8	90	150
4	10	50	110
5	10	90	150
6	12	90	150
7	14	90	150
8	16	90	150
9	10	140	200
10	12	140	200
11	14	140	200
12	16	140	200
13	18	140	200
14	20	140	200
15	22	180	250
16	25	180	250
17	10	280	340
18	12	280	340
19	14	280	340
20	16	280	340
21	18	280	340
22	20	280	340
23	22	280	340
24	25	280	340
25	14	420	500
26	16	420	500
27	18	420	500
28	20	420	500
29	22	420	500
30	25	420	500
31	28	420	500
32	14	520	600
33	16	520	600
34	18	520	600
35	20	520	600
36	22	520	600
37	25	520	600
38	28	520	600

Cross-head four-edge hammer drills

A 40Cr body and YG8 carbide direction use a cross cutting head and through-going chip channels. Square four-pit and round two-slot/two-pit holders require an exact equipment match.

Dimensions and configurations

23 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm

Configuration	Diameter mm	Working length mm	Overall length mm
1	6	45	110
2	6	75	140
3	8	90	150
4	10	50	110
5	10	90	150
6	12	90	150
7	14	90	150
8	16	90	150
9	10	140	200
10	12	140	200
11	14	140	200
12	16	140	200
13	18	140	200
14	20	140	200
15	22	180	250
16	25	180	250
17	12	280	340
18	14	280	340
19	16	280	340
20	18	280	340
21	20	280	340
22	22	280	340
23	25	280	340

Round and three-flat masonry impact drills

YG8 carbide tips and spiral flutes are offered for masonry drilling, with the shank form changing by the selected diameter.

Dimensions and configurations

9 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Shank

Configuration	Diameter mm	Overall length mm	Shank
1	3	60	round
2	4	80	round
3	5	90	round
4	6	100	round
5	8	110	round
6	10	120	three-flat
7	12	120	three-flat
8	14	150	three-flat
9	16	150	three-flat

Spring-steel demolition chisels

Forged, heat-treated spring-steel chisels include pointed and flat forms for concrete, brick and stone work. Square, round, five-pit and short/long hexagonal fitting directions need holder approval.

Square-interface extended hammer drills

A carbide cutting head and U-shaped chip groove combine with a four-pit square holder. Select the actual working reach and approved holder dimensions.

Dimensions and configurations

38 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm

Configuration	Diameter mm	Working length mm	Overall length mm
1	6	45	110
2	6	75	140
3	8	90	150
4	10	50	110
5	10	90	150
6	12	90	150
7	14	90	150
8	16	90	150
9	10	140	200
10	12	140	200
11	14	140	200
12	16	140	200
13	18	140	200
14	20	140	200
15	22	180	250
16	25	180	250
17	10	240	300
18	12	280	340
19	14	280	340
20	16	280	340
21	18	280	340
22	20	280	340
23	22	280	340
24	25	280	340
25	14	420	500
26	16	420	500
27	18	420	500
28	20	420	500
29	22	420	500
30	25	420	500
31	28	420	500
32	14	520	600
33	16	520	600
34	18	520	600
35	20	520	600
36	22	520	600
37	25	520	600
38	28	520	600

Five-pit hammer drills

40Cr steel and a YG8 carbide head combine with a U flute and a five-pit interface. Diameter bands and lengths are paired configuration references.

Dimensions and configurations

12 listed configurations · view dimensions

Configuration | Diameter band mm | Working length mm | Overall length mm

Configuration	Diameter band mm	Working length mm	Overall length mm
1	8–28	135	280
2	8–28	195	340
3	8–28	255	400
4	30–40	250	400
5	10–28	355	500
6	30–40	350	500
7	12–40	450	600
8	14–40	535	700
9	14–28	635	800
10	30–40	620	800
11	14–28	835	1000
12	30–40	820	1000

Long-hexagonal hammer drills

40Cr steel and a YG8 carbide tip pair with a long-hexagonal holder and chip-clearing flute. Approve the holder and the particular diameter band.

Dimensions and configurations

11 listed configurations · view dimensions

Configuration | Diameter band mm | Working length mm | Overall length mm

Configuration	Diameter band mm	Working length mm	Overall length mm
1	6–12	65	190
2	14–25	95	220
3	8–25	155	280
4	28–32	140	280
5	12–28	265	400
6	30–38	260	400
7	12–28	365	500
8	30–38	360	500
9	12–38	465	600
10	16–38	655	800
11	16–38	850	1000

Magnetic hex nut setters

Heat-treated CrV steel nut setters use a central magnet. Match the internal hex, outer diameter and shank to the fastener and driver.

Dimensions and configurations

10 listed configurations · view dimensions

Configuration | Internal hex mm | Outside diameter mm | Overall length mm | Shank mm

Configuration	Internal hex mm	Outside diameter mm	Overall length mm	Shank mm
1	6	10.5	65	6.3
2	7	12	65	6.3
3	8	12	65	6.3
4	9	13	65	6.3
5	10	13.5	65	6.3
6	11	16	65	6.3
7	12	16	65	6.3
8	13	16	65	6.3
9	14	19	65	6.3
10	17	23	65	6.3

Non-standard square-interface hammer drills

40Cr steel, a YG8 carbide head and U flute are shown in a non-standard square-interface drilling direction. Supply the hole and holder drawing for feasibility review.

Stated diameter direction

6–28 mm; selected length and interface require drawing confirmation

Brazed-diamond tile core drills

Brazed-diamond cutting edges address tile and selected stone/glass work. Cooling wax is configuration-specific and does not establish unlimited dry operation; tempered glass is excluded.

Dimensions and configurations

4 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	6	35	66	6
2	8	35	66	8
3	10	35	66	8
4	12	35	66	8

Cooling wax

Not present for the stated 12 mm and larger direction; confirm the selected item

Straight-shank HSS twist drills

Straight-shank HSS drills use spiral chip flutes. Approve the actual manufacturing process, alloy grade and geometry for the selected size.

Dimensions and configurations

105 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Pieces/box

Configuration	Diameter mm	Overall length mm	Pieces/box
1	0.3	16	10
2	0.4	17	10
3	0.5	19	10
4	0.6	21	10
5	0.7	25	10
6	0.8	27	10
7	0.9	29	10
8	1	31	10
9	1.1	33	10
10	1.2	35	10
11	1.3	35	10
12	1.4	37	10
13	1.5	37	10
14	1.6	40	10
15	1.7	43	10
16	1.8	43	10
17	1.9	45	10
18	2	46	10
19	2.1	46	10
20	2.2	50	10
21	2.3	50	10
22	2.4	54	10
23	2.5	54	10
24	2.6	54	10
25	2.7	58	10
26	2.8	58	10
27	2.9	58	10
28	3	58	10
29	3.1	62	10
30	3.2	62	10
31	3.3	67	10
32	3.4	67	10
33	3.5	67	10
34	3.6	67	10
35	3.7	67	10
36	3.8	72	10
37	3.9	72	10
38	4	72	10
39	4.1	72	10
40	4.2	77	10
41	4.3	77	10
42	4.4	77	10
43	4.5	77	10
44	4.6	77	10
45	4.7	77	10
46	4.8	83	10
47	4.9	83	10
48	5	83	10
49	5.1	83	10
50	5.2	83	10
51	5.3	83	10
52	5.4	90	10
53	5.5	90	10
54	5.6	90	10
55	5.7	90	10
56	5.8	90	10
57	5.9	90	10
58	6	90	10
59	6.1	98	10
60	6.2	98	10
61	6.3	98	10
62	6.4	98	10
63	6.5	98	10
64	6.6	98	10
65	6.7	98	10
66	6.8	106	10
67	6.9	106	10
68	7	106	10
69	7.1	106	5
70	7.2	106	5
71	7.3	106	5
72	7.4	106	5
73	7.5	106	5
74	7.6	114	5
75	7.7	114	5
76	7.8	114	5
77	7.9	114	5
78	8	114	5
79	8.1	114	5
80	8.2	114	5
81	8.3	114	5
82	8.4	114	5
83	8.5	114	5
84	8.6	122	5
85	8.7	122	5
86	8.8	122	5
87	8.9	122	5
88	9	122	5
89	9.1	122	5
90	9.2	122	5
91	9.3	122	5
92	9.4	122	5
93	9.5	122	5
94	9.6	130	5
95	9.7	130	5
96	9.8	130	5
97	9.9	130	5
98	10	130	5
99	10.1	130	5
100	10.2	130	5
101	10.3	130	5
102	10.4	130	5
103	10.5	130	5
104	10.6	130	5
105	10.7	139	5

Double-ended 9341 HSS drills

A 9341 HSS material direction combines two cutting ends with spiral flutes. Select the individual diameter and working reach.

Dimensions and configurations

11 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Pieces/box

Configuration	Diameter mm	Working length mm	Overall length mm	Pieces/box
1	3	15	48	10
2	3.2	16	48	10
3	3.5	17	48	10
4	4	18	53	10
5	4.2	18.5	53	10
6	4.5	19	53	10
7	5	20	58	10
8	5.2	20	58	10
9	5.5	20	58	10
10	6	22	62	10
11	6.2	22	62	10

Straight-flute through-hole taps

Straight flutes and a square drive end provide a through-hole tapping direction. Confirm the selected tap material and thread specification on an approved drawing.

Thread / pilot hole / pitch references

M2 /1.6 /0.4; M3 /2.5 /0.5; M4 /3.3 /0.7; M5 /4.2 /0.8; M6 /5 /1; M10 /8.5 /1.5 mm

Larger straight-shank HSS twist-drill direction

A larger-diameter HSS twist-drill direction shares the published straight-shank size chart. The selected diameter and manufacturing process require current confirmation.

Dimensions and configurations

18 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Pieces/box

Configuration	Diameter mm	Overall length mm	Pieces/box
88	9	122	5
89	9.1	122	5
90	9.2	122	5
91	9.3	122	5
92	9.4	122	5
93	9.5	122	5
94	9.6	130	5
95	9.7	130	5
96	9.8	130	5
97	9.9	130	5
98	10	130	5
99	10.1	130	5
100	10.2	130	5
101	10.3	130	5
102	10.4	130	5
103	10.5	130	5
104	10.6	130	5
105	10.7	139	5

Spiral, spiral-point and straight-flute machine taps

Distinct 6542 HSS and cobalt-HSS directions include spiral flutes for blind holes, spiral-point forms for through holes and straight-flute tools. Titanium-treated coating directions and square ends vary by selected tap.

Dimensions and configurations

7 listed configurations · view dimensions

6542 HSS spiral configuration | Thread | Flute length mm | Overall length mm | Round shank mm | Square drive mm | End

6542 HSS spiral configuration	Thread	Flute length mm	Overall length mm	Round shank mm	Square drive mm	End
1	M3×0.5	15	51	3	2.5	pointed
2	M4×0.7	20	56	4	3	pointed
3	M5×0.8	22	63	5	4	pointed
4	M6×1	26	70	6.3	5	pointed
5	M8×1.25	23	70	6.3	5	flat
6	M10×1.5	25	78	8	6	flat
7	M12×1.75	32	87	9	7	flat

Dimensions and configurations

7 listed configurations · view dimensions

Cobalt HSS spiral configuration | Thread | Flute length mm | Overall length mm | Round shank mm | Square drive mm | End

Cobalt HSS spiral configuration	Thread	Flute length mm	Overall length mm	Round shank mm	Square drive mm	End
1	M3×0.5	15	51	3	2.5	pointed
2	M4×0.7	20	56	4	3	pointed
3	M5×0.8	22	63	5	4	pointed
4	M6×1	26	70	6.3	5	pointed
5	M8×1.25	23	70	6.3	5	flat
6	M10×1.5	25	78	8	6	flat
7	M12×1.75	32	87	9	7	flat

Dimensions and configurations

7 listed configurations · view dimensions

Cobalt HSS spiral-point configuration | Thread | Flute length mm | Overall length mm | Round shank mm | Square drive mm | End

Cobalt HSS spiral-point configuration	Thread	Flute length mm	Overall length mm	Round shank mm	Square drive mm	End
1	M3×0.5	14	50	3	2.5	pointed
2	M4×0.7	19	57	4	3	pointed
3	M5×0.8	22	63	5	4	pointed
4	M6×1	26	69	6.3	5	pointed
5	M8×1.25	22	70	6.3	5	flat
6	M10×1.5	25	77	8	6	flat
7	M12×1.75	29	88	9	7	flat

Dimensions and configurations

9 listed configurations · view dimensions

6542 HSS straight-flute configuration | Thread | Flute length mm | Overall length mm | Round shank mm | Square drive mm | End

6542 HSS straight-flute configuration	Thread	Flute length mm	Overall length mm	Round shank mm	Square drive mm	End
1	M2×0.4	9	43	2.5	2	pointed
2	M3×0.5	18	50	3	2.5	pointed
3	M8×1.25	22	72	6.3	5	flat
4	M10×1.5	25	80	8	6	flat
5	M12×1.75	27	89	9	7	flat
6	M18×2.5	36	112	14	11	flat
7	M20×2.5	39	113	14	11	flat
8	M22×2.5	40	119	16	12.5	flat
9	M24×3	45	130	18	14	flat

Tap limit reference

H2 for the listed machine-tap directions; confirm selected thread and gauge acceptance

Pilot-hole references mm

M2×0.4:1.6; M3×0.5:2.5; M4×0.7:3.3; M5×0.8:4.2; M6×1:5; M8×1.25:6.8; M10×1.5:8.5; M12×1.75:10.3; M14×2:12; M16×2:14; M18×2.5:15.5; M20×2.5:17.5; M22×2.5:19.5; M24×3:21

Half-inch reduced-shank HSS drills

A reduced round shank and twin chip grooves support larger hole diameters. Workpiece hardness and material suitability require the selected tool application file.

Dimensions and configurations

8 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	14	108	160	12.7
2	14.5	108	160	12.7
3	15	108	160	12.7
4	15.5	108	160	12.7
5	16	108	160	12.7
6	16.5	108	160	12.7
7	17	108	160	12.7
8	17.5	108	160	12.7

HSS and cobalt-HSS drill assortments

Metal drill assortments combine selected HSS material grades with case-packed diameters. Confirm the exact component bill, grade and pack rather than interchanging sets.

Nominal 13-piece pack directions

4341, 9341, 6542 HSS or M35 cobalt HSS; listed diameter direction 1.5–6.5 mm, exact complete component bill requires approval

19-piece pack directions

9341, 6542 HSS or M35 cobalt HSS; 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10 mm

25-piece pack directions

9341, 6542 HSS or M35 cobalt HSS; 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5, 10, 10.5, 11, 11.5, 12, 12.5, 13 mm

Case construction

Hinged metal-style cases with upright size-indexed drill racks; approve selected case material and finish

Appearance directions

Gold-coloured and black M35 pack illustrations; finish appearance does not establish a coating chemistry

One-piece hex-shank twist drills

An integral hexagonal holder and spiral chip grooves provide a driving-tool drilling direction. The selected steel grade, diameter and lengths require current specification approval.

Diameter direction

1–13 mm

High-carbon-steel reduced-shank drills

High-carbon-steel drills combine reduced round shanks with spiral chip grooves. Select the work material and trial conditions rather than assuming stainless-steel suitability.

Dimensions and configurations

14 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	13.5	126	162	12.7
2	14	130	162	12.7
3	14.5	130	170	12.7
4	15	130	170	12.7
5	15.5	150	180	12.7
6	16	150	180	12.7
7	16.5	155	185	12.7
8	17	155	185	12.7
9	17.5	155	190	12.7
10	18	155	190	12.7
11	18.5	165	200	12.7
12	19	165	200	12.7
13	19.5	172	205	12.7
14	20	172	205	12.7

Taper-shank HSS twist drills

A taper-holder drilling direction uses HSS and a chip-clearing flute for larger holes. Approve the actual taper standard and machine match.

Dimensions and configurations

19 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Listed tail diameter mm

Configuration	Diameter mm	Working length mm	Overall length mm	Listed tail diameter mm
1	23.5	165	275	20
2	24	170	280	20
3	24.5	170	280	20
4	25	175	285	20
5	25.5	175	285	20
6	26	175	285	20
7	26.5	180	290	20
8	27	180	290	20
9	27.5	180	295	20
10	28	185	295	20
11	28.5	190	300	20
12	29	190	300	20
13	30	190	300	20
14	31	190	300	20
15	32	195	335	20
16	33	195	335	20
17	34	200	340	20
18	35	205	345	20
19	38	210	350	20

Long-series HSS twist drills

A longer-reach HSS twist-drill direction combines a round shank and spiral flutes. Keep flute length, overall reach and diameter paired in the selected row.

Dimensions and configurations

27 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Flute length mm

Configuration	Diameter mm	Overall length mm	Flute length mm
1	2	85	56
2	2.5	95	62
3	3	100	66
4	3.2	106	69
5	3.5	112	73
6	4	119	78
7	4.2	119	78
8	4.5	126	82
9	5	132	87
10	5.2	132	87
11	5.5	139	91
12	6	139	91
13	6.2	148	97
14	6.5	148	97
15	7	156	102
16	7.5	156	102
17	8	165	109
18	8.5	165	109
19	9	175	115
20	9.5	175	115
21	10	184	121
22	10.5	184	121
23	11	195	128
24	11.5	195	128
25	12	205	134
26	12.5	205	134
27	13	205	134

Diamond-grit glass and tile hole saws

Diamond-grit cutting rims, relief slots and a nickel-plated direction address glass, tile and selected stone. Water cooling is required for this direction and tempered glass is excluded.

Dimensions and configurations

46 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	6	30	55	6
2	8	30	55	8
3	10	30	55	8
4	12	30	55	8
5	14	30	55	8
6	16	30	55	8
7	18	30	55	8
8	20	30	55	8
9	21	30	55	8
10	22	30	55	8
11	25	30	55	8
12	26	30	55	8
13	27	30	55	8
14	28	30	55	8
15	30	30	55	8
16	32	30	55	8
17	34	30	55	8
18	35	30	55	10
19	38	30	55	10
20	40	30	55	10
21	42	30	55	10
22	45	30	55	10
23	48	30	55	10
24	50	30	55	10
25	53	30	55	10
26	55	30	55	10
27	60	30	55	10
28	70	30	55	10
29	75	30	55	10
30	80	30	55	10
31	85	30	55	10
32	90	30	55	10
33	95	30	55	10
34	100	30	55	10
35	105	30	55	10
36	110	30	55	10
37	120	30	55	10
38	125	30	55	10
39	130	30	55	10
40	135	30	55	10
41	140	30	55	10
42	150	30	55	10
43	160	30	55	10
44	170	30	55	10
45	180	30	55	10
46	200	30	55	10

Carbide-tip round-shank glass and tile drills

Brazed carbide tips and a round holder provide a glass/tile drilling direction. Use cooling water and the approved item instructions; tempered glass is excluded.

Dimensions and configurations

9 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm

Configuration	Diameter mm	Overall length mm
1	3	50
2	4	60
3	5	60
4	6	70
5	8	70
6	10	80
7	12	80
8	14	85
9	16	85

Three-edge carbide-tip metal hole saws

Inner, middle and outer cutting edges combine with an HSS pilot and a three-flat holder. Chip ports and the selected carbide direction support metal hole making.

Listed tip grade

YG10X; confirm selected item

Cutting depth direction

25 mm

Diameter references mm

14, 15, 16, 16.5, 17, 17.5, 18, 18.5, 19, 19.5, 20, 20.5, 21, 21.5, 22, 22.5, 23, 23.5, 24, 25, 26, 27, 28, 30, 32, 35, 38, 40, 42, 45, 48, 50, 53, 55, 60, 65, 70, 75, 80

Retail packing reference

1 piece/box

Illustrated rake-angle reference

5°; approve actual cutter drawing

HSS shallow metal hole saws

Ground HSS cutting edges, a pilot drill and a three-flat holder combine for selected metal-sheet and panel hole-making work.

Dimensions and configurations

42 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	14	7	70	8
2	15	8	70	8
3	16	8	70	8
4	17	8	70	8
5	17.5	8	70	8
6	18	8	70	8
7	18.5	8	70	8
8	19	8	70	8
9	19.5	8	70	8
10	20	8	70	8
11	20.5	8	70	8
12	21	8	70	8
13	21.5	8	70	8
14	22	8	70	8
15	22.5	8	70	8
16	23	8	70	8
17	24	8	70	8
18	25	9	70	8
19	25.5	9	70	8
20	26	9	70	8
21	27	9	70	8
22	28	9	70	8
23	30	9	70	8
24	32	9	70	8
25	35	10	70	9
26	38	10	70	9
27	40	10	70	9
28	42	10	70	9
29	45	10	70	9
30	48	10	70	9
31	50	10	70	9
32	53	10	70	9
33	55	10	70	10
34	60	10	70	10
35	65	10	70	10
36	70	10	70	10
37	75	10	70	10
38	80	10	70	10
39	85	10	70	10
40	90	10	70	10
41	95	10	70	10
42	100	10	70	10

Bi-metal wood hole saws

A toothed bi-metal cup, HSS pilot, chip ports and a three-flat arbor provide a wood hole-making direction. Confirm the cup, pilot and actual assembly dimensions.

Dimensions and configurations

39 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	16	25	81	10
2	18	25	81	10
3	20	25	81	10
4	22	25	81	10
5	25	25	81	10
6	26	25	81	10
7	28	25	81	10
8	30	25	81	10
9	32	25	81	10
10	35	25	81	10
11	38	25	82	10
12	40	25	82	10
13	42	25	82	10
14	45	25	82	10
15	50	25	82	10
16	53	25	82	10
17	55	25	82	10
18	60	25	94	10
19	65	32	94	10
20	70	32	94	10
21	75	32	94	10
22	80	32	96	10
23	85	32	96	10
24	90	32	96	10
25	95	32	100	10
26	100	32	100	10
27	105	32	100	10
28	110	37	100	10
29	115	37	100	10
30	120	37	100	10
31	125	37	100	10
32	130	37	100	10
33	140	37	100	10
34	150	37	100	10
35	160	37	100	10
36	170	37	100	10
37	180	37	100	10
38	190	37	100	10
39	200	37	100	10

Three-flat-shank multi-material carbide drills

A carbide cutting head, three-flat holder and double spiral chip grooves provide a multi-material drilling direction. Match cooling and drilling mode to the actual surface; tempered glass is excluded.

Dimensions and configurations

4 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	6	57	100	5
2	8	70	117	6
3	10	75	122	8
4	12	75	124	8

Carbide-tip wood boring cutters

A curved three-edge head, ground carbide cutting edges and round shank provide a wood boring direction. Confirm the individual diameter and shank pair.

Diameter direction

16–60 mm

Overall length reference

85 mm

Shank direction

8–10 mm, matched to selected cutter

Bi-metal hole saws for wood, thin sheet and PVC

A toothed bi-metal cup, HSS pilot, chip ports and three-flat arbor support selected wood, thin-metal and PVC hole making. Approve the cup and pilot assembly for the actual material.

Dimensions and configurations

39 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	16	25	81	10
2	18	25	81	10
3	20	25	81	10
4	22	25	81	10
5	25	25	81	10
6	26	25	81	10
7	28	25	81	10
8	30	25	81	10
9	32	25	81	10
10	35	25	81	10
11	38	25	82	10
12	40	25	82	10
13	42	25	82	10
14	45	25	82	10
15	50	25	82	10
16	53	25	82	10
17	55	25	82	10
18	60	32	94	10
19	65	32	94	10
20	70	32	94	10
21	75	32	94	10
22	80	32	96	10
23	85	32	96	10
24	90	32	96	10
25	95	32	100	10
26	100	32	100	10
27	105	32	100	10
28	110	37	100	10
29	115	37	100	10
30	120	37	100	10
31	125	37	100	10
32	130	37	100	10
33	140	37	100	10
34	150	37	100	10
35	160	37	100	10
36	170	37	100	10
37	180	37	100	10
38	190	37	100	10
39	200	37	100	10

Carbide-tip deep metal hole saws

Carbide cutting edges, a pilot drill, raked teeth and a three-flat holder form a deeper-cup metal hole-making direction. Select the appropriate sheet or panel material.

Dimensions and configurations

30 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	16	20	88	10
2	18	20	88	10
3	18.5	20	88	10
4	19	20	88	10
5	19.5	20	88	10
6	20	20	88	10
7	22	20	88	10
8	22.5	20	88	10
9	23	20	88	10
10	23.5	20	88	10
11	25	20	88	10
12	28	20	88	10
13	30	20	88	10
14	32	20	88	10
15	32.5	20	88	10
16	35	20	88	10
17	38	20	88	10
18	40	20	88	10
19	45	20	88	10
20	50	20	88	10
21	55	20	88	10
22	60	20	88	10
23	65	20	88	10
24	70	20	88	10
25	75	20	88	10
26	80	20	88	10
27	85	20	88	10
28	90	20	88	10
29	95	20	88	10
30	100	20	88	10

Ground HSS shallow metal hole cutters

Ground HSS teeth, a pilot drill and a three-flat holder provide shallow-cup hole making. Different cup diameters use different working depths and shanks.

Dimensions and configurations

42 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	14	7	73	8
2	15	8	70	8
3	16	8	70	8
4	17	8	70	8
5	17.5	8	70	8
6	18	8	70	8
7	18.5	8	70	8
8	19	8	70	8
9	19.5	8	70	8
10	20	8	70	8
11	20.5	8	70	8
12	21	8	70	8
13	21.5	8	70	8
14	22	8	70	8
15	22.5	8	70	8
16	23	8	70	8
17	24	8	70	8
18	25	9	70	8
19	25.5	9	70	8
20	26	9	70	8
21	27	9	70	8
22	28	9	70	8
23	30	9	70	8
24	32	9	70	8
25	35	10	70	9
26	38	10	70	9
27	40	10	70	9
28	42	10	70	9
29	45	10	70	9
30	48	10	70	9
31	50	10	70	9
32	53	10	70	9
33	55	10	70	10
34	60	10	70	10
35	65	10	70	10
36	70	10	70	10
37	75	10	70	10
38	80	10	70	10
39	85	10	70	10
40	90	10	70	10
41	95	10	70	10
42	100	10	70	10

Multi-tooth carbide shallow-cup hole saws

Multiple raked carbide teeth, a pilot and a three-flat shank form a shallow metal-hole cutting direction. Confirm the required internal cup clearance.

Dimensions and configurations

27 listed configurations · view dimensions

Configuration | Diameter mm | Internal cup depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Internal cup depth mm	Overall length mm	Shank mm
1	16	10	75	9.8
2	16.5	10	75	9.8
3	17	10	75	9.8
4	18	10	75	9.8
5	18.5	10	75	9.8
6	19	10	75	9.8
7	19.5	10	75	9.8
8	20	10	75	9.8
9	20.5	10	75	9.8
10	21	10	75	9.8
11	22	10	75	9.8
12	22.5	10	75	9.8
13	23	10	75	9.8
14	24	10	75	9.8
15	25	10	75	9.8
16	25.5	10	75	9.8
17	26	10	75	9.8
18	28	10	75	9.8
19	30	10	75	9.8
20	32	10	75	9.8
21	35	10	75	9.8
22	38	10	75	9.8
23	40	10	75	9.8
24	42	10	75	9.8
25	45	10	75	9.8
26	48	10	75	9.8
27	50	10	75	9.8

Carbide-tip steel hole cutter range

Carbide-tipped cup cutters use a centre pilot and flat-sided round holder. Different cutter diameters and tooth layouts require the actual sample and drawing.

Diameter directions

14–23.5 mm; 24–75 mm; 80–100 mm; individual sizes require current confirmation

Carbide-tip wood and panel saw blades

Alloy-steel plate bodies and carbide-tip teeth combine with heat-relief slots and protective edge sleeves. The selected row separates ripping, crosscutting, plywood, formwork and enclosed-saw uses.

Dimensions and configurations

39 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Bore mm | Teeth | Application direction | Tooth layout

Configuration	Outside diameter mm	Tooth width mm	Bore mm	Teeth	Application direction	Tooth layout
1	110	1.6	20	30	wood rip	alternating
2	110	1.6	20	40	wood crosscut	multi-purpose tooth layout
3	110	1.8	20	50	plywood	alternating
4	125	1.8	20	40	enclosed/dustless saw application	alternating
5	150	2	25.4	40	wood rip	alternating
6	150	2	25.4	60	wood crosscut	alternating
7	180	2	25.4	40	wood crosscut	alternating
8	180	2	25.4	60	wood crosscut	alternating
9	180	2	25.4	80	wood crosscut	alternating
10	180	2.2	25.4	52	formwork	alternating
11	200	2.2	25.4	40	wood rip	alternating
12	200	2.2	25.4	60	wood crosscut	alternating
13	200	2.2	25.4	80	wood crosscut	alternating
14	200	2.2	25.4	100	wood crosscut	alternating
15	230	2.4	25.4	40	wood rip	alternating
16	230	2.4	25.4	60	wood crosscut	alternating
17	230	2.4	25.4	80	wood crosscut	alternating
18	230	2.4	25.4	100	wood crosscut	alternating
19	230	2.4	25.4	52	formwork	alternating
20	250	2.6	25.4 or 30	40	wood rip	alternating
21	250	2.6	25.4 or 30	60	wood crosscut	alternating
22	250	2.6	25.4 or 30	80	wood crosscut	alternating
23	250	2.6	25.4 or 30	100	wood crosscut	alternating
24	250	2.6	25.4 or 30	120	wood crosscut	alternating
25	300	3	25.4 or 30	40	wood rip	alternating
26	300	3	25.4 or 30	60	wood crosscut	alternating
27	300	3	25.4 or 30	80	wood crosscut	alternating
28	300	3	25.4 or 30	100	wood crosscut	alternating
29	300	3	25.4 or 30	120	wood crosscut	alternating
30	350	3.2	25.4 or 30	40	wood rip	alternating
31	350	3.2	25.4 or 30	60	wood crosscut	alternating
32	350	3.2	25.4 or 30	80	wood crosscut	alternating
33	350	3.2	25.4 or 30	100	wood crosscut	alternating
34	350	3.2	25.4 or 30	120	wood crosscut	alternating
35	400	3.4	30	40	wood rip	alternating
36	400	3.4	30	60	wood crosscut	alternating
37	400	3.4	30	80	wood crosscut	alternating
38	400	3.4	30	100	wood crosscut	alternating
39	400	3.4	30	120	wood crosscut	alternating

HCS jigsaw blades for straight and curved cuts

Heat-treated HCS blades use ground side-set teeth. Straight-cut and narrower curve-cut shapes are separate directions for wood and PVC.

Straight-cut blade

HCS; 4 mm tooth pitch; 74 mm working length; 100 mm overall length

Curve-cut blade

HCS; 4 mm tooth pitch; 74 mm working length; 100 mm overall length

Workpiece reference

Softwood 5–50 mm, selected board/fibreboard and PVC coarse cutting; approve the actual blade and material

Diamond wall-grooving discs

Diamond-grit cutting discs include segmented and wet/dry-use construction directions, with individual hanging retail packs. Approve the actual rim, machine and cooling instructions.

Configuration 1

Outside diameter 110 mm; bore 20 mm; rim width 1.8 mm

Configuration 2

Outside diameter 114 mm; bore 20 mm; rim width 1.8 mm

Construction and pack directions

Segmented, wet-cut and dry-cut selections; hanging card/blister-style retail packs

Reciprocating blades for wood, metal and demolition

Separate HCS and bi-metal blade constructions use ground or milled side-set teeth. Match tooth pitch and blade reach to the actual stock, pipe or demolition material.

Fine bi-metal / short

150×19×0.9 mm; pitch 1.4 mm; thin metal 1.5–4 mm and pipe/profile diameter 5–100 mm reference

Coarse HCS / short

150×19×1.25 mm; pitch 4 mm; construction wood 6–100 mm, boards below 75 mm and fibreboard reference

Coarse HCS / medium

225×19×1.25 mm; pitch 4 mm; construction wood 10–100 mm, plastic profiles 5–175 mm and pipe/profile 8–50 mm reference

Fine bi-metal / medium

225×19×0.9 mm; pitch 1.4 mm; thin metal 1.5–4 mm and pipe/profile diameter 5–175 mm reference

Variable-pitch bi-metal / long

300×19×0.9 mm; pitch 1.8–2.5 mm; thin metal or nailed wood 5–250 mm, aluminium profiles 3–10 mm and plastic 3–250 mm reference

Coarse HCS / long

300×19×1.25 mm; pitch 4 mm; chipboard 10–250 mm, plastic 5–250 mm and pipe/profile 5–60 mm reference

Outdoor wood HCS

240×19×1.25 mm; pitch 5 mm; outdoor timber diameter 15–150 mm and rough timber reference

Diamond wall and floor grooving blades

Diamond cutting rims and relief-slot patterns address wall, concrete, stone and floor grooving. Wet-cut constructions require the actual cooling setup.

Wet-cut configuration 1

Outside diameter 133 mm; bore 22.23 mm; thickness 2 mm

Wet-cut configuration 2

Outside diameter 168 mm; bore 22.23 mm; thickness 2.2 mm

Wet-cut configuration 3

Outside diameter 190 mm; bore 22.23 mm; thickness 2.2 mm

Segmented configuration

Outside diameter 114 mm; bore 20 mm; thickness 2 mm

Additional rim directions

114 mm outside diameter /20 mm bore; exact thickness and rim selection require approval

Fine-corrugated diamond tile blades

Diamond cutting rims include fine radial and curved corrugated face patterns for vitrified and microcrystalline tile. The selected construction requires sample and finish review.

Geometry reference

Outside diameter 105 mm; bore 20 mm; thickness 1.2 mm

Construction directions

Fine radial rim, curved corrugation and reinforced/ported body layouts

Carbide wood blades with application-specific tooth layouts

A separate carbide-tip series offers alloy plate bodies, relief slots and edge protection. The selected dimensions distinguish ripping, crosscutting, plywood and formwork work.

Dimensions and configurations

37 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Bore mm | Teeth | Application direction | Tooth layout

Configuration	Outside diameter mm	Tooth width mm	Bore mm	Teeth	Application direction	Tooth layout
1	110	1.8	20	30	wood rip	alternating
2	110	1.8	20	40	wood crosscut	multi-purpose tooth layout
3	110	1.8	20	50	plywood	alternating
4	125	1.8	20	40	enclosed/dustless saw application	alternating
5	150	2.2	25.4	40	wood crosscut	alternating
6	150	2.2	25.4	60	wood crosscut	alternating
7	180	2	25.4	40	wood rip	alternating
8	180	2	25.4	60	wood crosscut	alternating
9	180	2	25.4	80	wood crosscut	alternating
10	180	2.2	25.4	52	formwork	alternating
11	200	2.4	25.4	40	wood rip	alternating
12	200	2.4	25.4	60	wood crosscut	alternating
13	230	2.2	25.4	40	wood rip	alternating
14	230	2.2	25.4	60	wood crosscut	alternating
15	230	2.4	25.4	80	wood crosscut	alternating
16	230	2.4	25.4	100	wood crosscut	alternating
17	230	2.4	25.4	52	formwork	alternating
18	254	2.4	25.4 or 30	40	wood rip	alternating
19	254	2.4	25.4 or 30	60	wood crosscut	alternating
20	254	2.6	25.4 or 30	80	wood crosscut	alternating
21	254	2.6	25.4 or 30	60	wood crosscut	alternating
22	254	2.6	25.4 or 30	100	wood crosscut	alternating
23	300	2.6	25.4 or 30	40	wood rip	alternating
24	300	2.6	25.4 or 30	60	wood crosscut	alternating
25	300	3	25.4 or 30	80	wood crosscut	alternating
26	300	3	25.4 or 30	100	wood crosscut	alternating
27	300	3	25.4 or 30	120	wood crosscut	alternating
28	350	3	25.4 or 30	40	wood rip	alternating
29	350	3	25.4 or 30	60	wood rip	alternating
30	350	3.2	25.4 or 30	80	wood crosscut	alternating
31	350	3.2	25.4 or 30	100	wood crosscut	alternating
32	350	3.2	25.4 or 30	120	wood crosscut	alternating
33	400	3.2	30	40	wood rip	alternating
34	400	3.2	30	60	wood rip	alternating
35	400	3.4	30	80	wood crosscut	alternating
36	400	3.4	30	100	wood crosscut	alternating
37	400	3.4	30	120	wood crosscut	alternating

Diamond vitrified-tile and panel blades

A fine diamond rim is offered for tile, vitrified and microcrystalline panel cutting. Confirm the surface, cutting conditions and selected construction.

Geometry reference

Outside diameter 105 mm; bore 20 mm; thickness 1.4 mm

Rim directions

Two illustrated fine-rim construction/finish directions; approve actual sample

Carbide-tip aluminium circular saw blades

Trapezoid/flat tooth geometry, alloy-steel plate bodies, relief slots and edge protection address selected aluminium profiles. Keep the bore and tooth width paired with the selected blade.

Dimensions and configurations

17 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Bore mm | Teeth

Configuration	Outside diameter mm	Tooth width mm	Bore mm	Teeth
1	180	2.2	25.4	80
2	200	2.2	25.4	80
3	200	2.2	25.4	100
4	230	2.6	25.4	80
5	230	2.6	25.4	100
6	254	2.8	25.4 or 30	100
7	254	2.8	25.4 or 30	120
8	300	3	25.4 or 30	100
9	300	3	25.4 or 30	120
10	350	3.2	25.4 or 30	100
11	350	3.2	25.4 or 30	120
12	400	3.4	30	100
13	400	3.4	30	120
14	450	4	30	100
15	450	4	30	120
16	500	4	30	100
17	500	4	30	120

Sintered diamond cup grinding wheels

Hot-pressed sintered diamond grinding faces include segmented and fine-corrugated directions for concrete, stone, walls and floors. Select the machine flange, guard and surface trial together.

Configuration 1

Outside diameter 100 mm; listed grinding-section thickness 9 mm; bore 22.23 mm; curved segmented face

Configuration 2

Outside diameter 100 mm; listed grinding-section thickness 6 mm; bore 22.23 mm; fine-corrugated face

Configuration 3

Outside diameter 100 mm; listed grinding-section thickness 9 mm; bore 22.23 mm; segmented construction direction

Configuration 4

Outside diameter 100 mm; listed grinding-section thickness 6 mm; bore 20 mm; fine-corrugated face

Configuration 5

Outside diameter 125 mm; listed grinding-section thickness 9 mm; bore 22.23 mm; segmented face

Reinforced abrasive metal cutting discs

Thin double-mesh fibre reinforcement supports selected metal and stainless-steel cutting disc directions. Confirm the exact marked disc, mounting, machine and intended operation.

Illustrated small-disc geometry

Outside diameter 107 mm; thickness 1.2 mm; bore 16 mm

Illustrated disc marking

41-WA60RBF; marked maximum 14200 rpm /80 m/s for the illustrated 107 mm disc only; approve the delivered item marking

Additional diameter directions

350 and 400 mm; thickness, bore, grade and rated speed require separate confirmation

Carbide-tip engineered-panel saw blades

Alternating carbide teeth and protected edges address selected lower/medium-density engineered panels and furniture processing. Match actual tooth count, kerf and bore to the machine and panel.

Dimensions and configurations

5 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Teeth directions | Bore mm

Configuration	Outside diameter mm	Tooth width mm	Teeth directions	Bore mm
1	180	2.3	80	25.4
2	200	2.3	80 or 100	25.4
3	230	2.6	80 or 100	25.4
4	254	3	100 or 120	25.4 or 30
5	300	3.2	100 or 120	25.4 or 30

Pneumatic brad, pin and staple fastening tools

Separate pneumatic tools cover brad, headless-pin, steel-nail, upholstery, panel and frame fastening. Selected versions feature a quick-release magazine, fastener view window, hardened magazine surface and rubber grip.

Dimensions and configurations

11 listed configurations · view dimensions

Configuration | Fastener direction | Capacity pieces | Fastener length mm | Net mass kg | Working pressure bar | Recommended hose mm

Configuration	Fastener direction	Capacity pieces	Fastener length mm	Net mass kg	Working pressure bar	Recommended hose mm
1	Brad versionA	100	10–30	1.1	4–8	5×8
2	Brad versionB	100	10–30	1.1	4–8	5×8
3	Headless pin	100	10–25	0.85	4–8	5×8
4	Steel-nail long	75	18–64	3	4–8	5×8
5	Steel-nail short	80	18–38	2.1	4–8	5×8
6	Long brad	100	25–50	2.1	4–8	5×8
7	Narrow staple	100	10–22	1.1	4–8	5×8
8	Upholstery staple	100	6–13	0.85	4–8	5×8
9	Panel staple	100	10–22	1.1	4–8	5×8
10	Rolled-foot stapler	150	16–25	3.5	4–8	5×8
11	Frame stapler	150	25–51	3.2	4–8	5×8

Fastener profile references

Pin direction: 0.63 mm pin; narrow staple direction: 0.6 mm wire / 4 mm crown; wider staple directions: 0.6 mm wire / 10 mm crown; heavy staple directions: 1.6×1.4 mm wire / 10.6 mm crown; selected steel-nail direction: 2.2 mm shank; selected T-nail direction: 1.6×1.4 mm wire. Match the fastener profile to the approved tool.

Nailer driver and piston replacement assemblies

Replacement piston-and-driver assemblies are illustrated for different pneumatic fastening tools. Send the tool identification privately, part drawing, dimensions and a sample for an exact compatibility check.

Pneumatic nailer seal and wear-part sets

Sealing-ring and related wear-part sets complement selected pneumatic nailers. Confirm each part number privately, section dimensions, material, quantity and the actual repair assembly.

Reversible pneumatic screwdrivers

A self-locking bit holder, trigger, forward/reverse selection, air adjustment and multi-hole exhaust support assembly and repair work. Selected bit, hex and socket fittings require holder approval.

Compact directionA

Approximate overall length 215 mm; trigger lever length 90 mm; recommended hose 5×8 mm

Compact directionB

Approximate overall length 215 mm; trigger lever length 90 mm; recommended hose 5×8 mm

Long direction

Approximate overall length 240 mm; trigger lever length 95 mm; recommended hose 5×8 mm

S2 combination cross/slotted driver bits

S2 alloy steel, a magnetic working end, hexagonal holder and protective sleeve provide combination-head driving for selected fittings. Approve the exact screw-head profile and application.

Dimensions and configurations

3 listed configurations · view dimensions

Configuration | Tip width mm | Overall length mm

Configuration	Tip width mm	Overall length mm
1	5.5	65
2	5.5	110
3	5.5	150

Transparent TPU pneumatic hose

Transparent TPU hose helps make contamination inside the line visible. Select the actual connectors, pressure rating, temperature conditions and bending requirement for the tool installation.

Dimensions and configurations

3 listed configurations · view dimensions

Configuration | Inside diameter mm | Outside diameter mm | Roll length m

Configuration	Inside diameter mm	Outside diameter mm	Roll length m
1	5	8	100
2	6.5	10	100
3	8	12	100

Adjustable pneumatic paint spray guns

A heat-treated stainless nozzle direction combines an adjustable air cap, fan and fluid controls, a two-stage trigger and a lower paint-cup layout. Discuss the coating, viscosity, finish and actual air supply for wood, wall and vehicle refinishing.

Material direction

Stainless nozzle and stainless-body directions; approve selected alloy and finish

Adjustment direction

Air-cap orientation, spray fan and paint flow controls

Air and coating configuration

Nozzle size, cup capacity, air consumption and valid pressure rating require the selected item file

Magnetic CrV screwdrivers and reversible drivers

Cross-head and slotted CrV screwdrivers use non-slip handles and magnetic ends. Reversible drivers add a chrome-finished, heat-treated double-ended rod and a spring-release collar for position adjustment and exchange.

Dimensions and configurations

10 listed configurations · view dimensions

Cross head configuration | Shaft diameter mm | Exposed shaft length mm | Overall length mm

Cross head configuration	Shaft diameter mm	Exposed shaft length mm	Overall length mm
1	3	76	158
2	5	76	170
3	5	100	195
4	5	151	245
5	6	100	209
6	6	128	232
7	6	151	258
8	6	200	307
9	6	250	356
10	6	300	408

Dimensions and configurations

10 listed configurations · view dimensions

Slotted head configuration | Shaft diameter mm | Exposed shaft length mm | Overall length mm

Slotted head configuration	Shaft diameter mm	Exposed shaft length mm	Overall length mm
1	3	76	158
2	5	76	170
3	5	100	195
4	5	153	245
5	6	100	209
6	6	128	232
7	6	154	258
8	6	200	308
9	6	250	356
10	6	300	408

Reversible long-rod driver

PH2/slotted approximately 6.3 mm ends; handle 110 mm; detachable rod 180 mm; assembled overall length requires approval

Reversible short-rod driver

PH2/slotted approximately 6.3 mm ends; handle 116 mm; detachable rod 140 mm; assembled overall length requires approval

Locking steel tape measures

A high-carbon-steel blade combines rust-protective treatment, a matte printed scale and a protective film. ABS housing, manual/top locking, automatic return, a movable end hook, wrist cord and belt clip are configuration directions.

Illustrated length directions

3 m and 5 m blade markings; confirm the selected tape length and width

Measurement features

Sliding end hook for inside/outside reference and scale protection layers

Nine-piece ball-end hex and star key sets

Forged CrV keys use a plated finish, a one-piece bent profile and an indexed clip holder. Ball-end hex, flat-end and star-head directions support different fastener access requirements.

Ball-end hex size 1.5

Medium long/short sides 66/17; extra-long 85/18; listed dimension units require drawing confirmation

Ball-end hex size 2

Medium long/short sides 75/19; extra-long 94/20; listed dimension units require drawing confirmation

Ball-end hex size 2.5

Medium long/short sides 83/22; extra-long 106/23; listed dimension units require drawing confirmation

Ball-end hex size 3

Medium long/short sides 95/24; extra-long 124/24; listed dimension units require drawing confirmation

Ball-end hex size 4

Medium long/short sides 108/28; extra-long 142/28; listed dimension units require drawing confirmation

Ball-end hex size 5

Medium long/short sides 121/32; extra-long 159/34; listed dimension units require drawing confirmation

Ball-end hex size 6

Medium long/short sides 141/35; extra-long 181/39; listed dimension units require drawing confirmation

Ball-end hex size 8

Medium long/short sides 158/43; extra-long 200/42; listed dimension units require drawing confirmation

Ball-end hex size 10

Medium long/short sides 181/53; extra-long 221/53; listed dimension units require drawing confirmation

Star sizeT10

Medium long/short sides 68/18; extra-long 93/19; listed dimension units require drawing confirmation

Star sizeT15

Medium long/short sides 76/21; extra-long 100/21; listed dimension units require drawing confirmation

Star sizeT20

Medium long/short sides 86/24; extra-long 112/25; listed dimension units require drawing confirmation

Star sizeT25

Medium long/short sides 95/28; extra-long 123/28; listed dimension units require drawing confirmation

Star sizeT27

Medium long/short sides 104/29; extra-long 144/29; listed dimension units require drawing confirmation

Star sizeT30

Medium long/short sides 113/31; extra-long 145/35; listed dimension units require drawing confirmation

Star sizeT40

Medium long/short sides 123/40; extra-long 171/39; listed dimension units require drawing confirmation

Star sizeT45

Medium long/short sides 142/46; extra-long 197/46; listed dimension units require drawing confirmation

Star sizeT50

Medium long/short sides 158/49; extra-long 221/50; listed dimension units require drawing confirmation

Set construction

9 keys per listed set, medium and extra-long directions, clip-type indexed holder

Single-edge and double-edge straight router cutters

Straight woodworking cutters include a single-edge geometry table and separate double-edge physical cutter directions. Confirm the actual cutting form, substrate and drawing for the selected cutter.

Dimensions and configurations

7 listed configurations · view dimensions

Configuration | Cutting edges | Quarter-inch shank reference | Listed D | Listed H

Configuration	Cutting edges	Quarter-inch shank reference	Listed D	Listed H
1	1	1/4 inch	2.38	13
2	1	1/4 inch	3.17	13
3	1	1/4 inch	3.96	13
4	1	1/4 inch	4.76	13
5	1	1/4 inch	6.35	20
6	1	1/4 inch	7.96	20
7	1	1/4 inch	9.5	25

Additional direction

Double-edge straight cutters; exact D/H and shank require a selected drawing

Dimension qualification

D/H values are drawing references; their unit is not printed in this table and must be confirmed

Magnetic double-ended cross driver bits

Double-ended cross bits include a removable magnetic collar and plain bit directions. S2 and other alloy-steel selections have separate material and length combinations.

Magnetic-collar direction

Cross head; high-strength alloy steel; overall 65 mm;10 pieces/box

Profiled plain direction

Alloy-steel grade and actual cross-head size require approval;65 mm;10 pieces/box

S2 cross bits

PH2;65 or 110 mm;10 pieces/box

Alloy-steel cross bits

PH2;65,110,150 or 200 mm;10 pieces/box

S2 magnetic hex driver bits

Forged, heat-treated S2 steel combines with a magnetized hex working end and a hexagonal shank. Select the actual fastener size and required reach.

Dimensions and configurations

15 listed configurations · view dimensions

Configuration | Working hex size mm | Overall length mm | Shank mm

Configuration	Working hex size mm	Overall length mm	Shank mm
1	3	50	6.35
2	4	50	6.35
3	5	50	6.35
4	6	50	6.35
5	3	100	6.35
6	4	100	6.35
7	5	100	6.35
8	6	100	6.35
9	3	150	6.35
10	4	150	6.35
11	5	150	6.35
12	3	200	6.35
13	4	200	6.35
14	5	200	6.35
15	6	200	6.35

Steel core-drilling extension rods

A one-piece steel extension direction uses a textured finish, grip slots and threaded connections. Select the holder, thread pitch, handedness and reach on an approved drawing.

Dimensions and configurations

7 listed configurations · view dimensions

Configuration | Listed outer connection diameter mm | Listed inner connection diameter mm | Overall length mm

Configuration	Listed outer connection diameter mm	Listed inner connection diameter mm	Overall length mm
1	30	22	160
2	30	22	200
3	30	22	230
4	30	22	300
5	30	22	400
6	30	22	500
7	30	22	1000

Cross-head hex-shank carbide ceramic drills

Four cutting edges and a U-shaped chip flute combine with a hexagonal holder for ceramic, wall and selected multi-material work. Cooling is material-specific; reinforced-steel contact and tempered glass are excluded.

Dimensions and configurations

4 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	6	40	99	6.35
2	8	47	100	6.35
3	10	66	117	6.35
4	12	70	119	6.35

Carbide-tip wall core and arbor assemblies

A core cup, centre pilot, fixing screw and connecting rod form a wall-hole drilling assembly. Inner/outer chip-clearance features and round/square holder directions address selected concrete and brick service openings.

Dimensions and configurations

20 listed configurations · view dimensions

Configuration | Core diameter mm | Working depth mm | Teeth

Configuration	Core diameter mm	Working depth mm	Teeth
1	30	70	4
2	35	70	5
3	40	70	5
4	45	70	5
5	50	70	5
6	55	70	5
7	60	70	6
8	65	70	8
9	70	70	8
10	75	70	8
11	80	70	8
12	85	70	8
13	90	70	9
14	95	70	9
15	100	70	10
16	105	70	12
17	110	70	14
18	120	70	14
19	125	70	14
20	150	70	16

Rod length direction

110–430 mm, selected connection and assembly require approval

Holder directions

Round and square hammer-tool interfaces; exact holder drawing required

Wall core cutters with matched connecting rods

Carbide core cups pair with a centre pilot and the selected round or square holder. Approve the complete assembly, working reach and cooling instructions for the wall material.

Dimensions and configurations

20 listed configurations · view dimensions

Configuration | Core diameter mm | Working depth mm | Teeth

Configuration	Core diameter mm	Working depth mm	Teeth
1	30	70	4
2	35	70	5
3	40	70	5
4	45	70	5
5	50	70	5
6	55	70	5
7	60	70	6
8	65	70	8
9	70	70	8
10	75	70	8
11	80	70	8
12	85	70	8
13	90	70	9
14	95	70	9
15	100	70	10
16	105	70	12
17	110	70	14
18	120	70	14
19	125	70	14
20	150	70	16

Rod length direction

110–430 mm, selected connection and assembly require approval

Holder directions

Round and square hammer-tool interfaces; exact holder drawing required

Long-reach carbide wood boring cutters

A carbide cutting head with curved side edges and a centre point addresses softwood, hardwood, plywood, composite panels and selected plastic. Confirm the actual cutting geometry and reach.

Dimensions and configurations

4 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Listed working length mm | Shank mm

Configuration	Diameter mm	Overall length mm	Listed working length mm	Shank mm
1	18	125	95	8
2	20	125	95	8
3	25	125	95	8
4	28	125	95	8

Sintered diamond stone core cutters

Hot-pressed sintered diamond heads combine segmented cutting rims, oval chip-clearance ports and a three-flat holder. Selected marble, granite, pebble and tile drilling requires continuous water cooling; tempered glass is excluded.

Dimensions and configurations

28 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	6	55	72	6
2	8	55	72	8
3	10	58	72	8
4	12	58	82	10
5	14	58	82	10
6	16	58	82	10
7	18	58	82	10
8	20	58	82	10
9	22	58	82	10
10	25	58	82	10
11	28	60	82	10
12	30	60	85	10
13	32	60	85	10
14	35	60	85	10
15	38	60	85	10
16	40	60	85	10
17	45	60	85	10
18	50	60	85	10
19	55	60	85	10
20	60	60	85	10
21	65	60	85	10
22	70	60	85	10
23	75	60	85	10
24	80	60	85	10
25	85	60	85	10
26	90	60	85	10
27	95	60	85	10
28	100	60	85	10

Extended hex-shank carbide wood boring cutters

A carbide cutting head, curved three-edge structure and spiral chip-clearance direction address wood, walnut, composite and multilayer panels. Select the actual head geometry and holder.

Dimensions and configurations

9 listed configurations · view dimensions

Configuration | Diameter mm | Working depth mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working depth mm	Overall length mm	Shank mm
1	16	80	130	6.3
2	18	80	130	6.3
3	20	80	130	6.3
4	22	80	130	6.3
5	25	80	130	6.3
6	28	80	130	6.3
7	30	80	130	6.3
8	32	80	130	6.3
9	35	80	130	6.3

Pipe hole-saw assemblies

A toothed cup, pilot drill, chip ports and hexagonal holder provide pipe connection hole making. Match the actual fitting drawing, pipe wall, fixture and cutting-edge construction before trial.

Dimensions and configurations

7 listed configurations · view dimensions

Configuration | Cut diameter mm | Overall length mm | Working depth mm | Shank reference mm

Configuration	Cut diameter mm	Overall length mm	Working depth mm	Shank reference mm
1	38	118	44	11
2	46	118	44	11
3	51	118	44	11
4	76	118	44	11
5	81	118	44	11
6	89	118	44	11
7	114	118	44	11

Application reference

Galvanised-steel pipe wall 0.5–5 mm; confirm selected cutter, fixture and operating file

Illustrated fitting references

100×25 tee:38 mm hole;100×32:46 mm;100×40:51 mm;100×65:81 mm;100×80:89 mm;100×100:114 mm. These are illustrated fitting references and require the actual fitting drawing.

Thin-kerf carbide wood saw blades

Selected thin-kerf carbide-tip blade directions address wood conservation and different tooth-count finishes. Keep tooth width and bore paired with the actual diameter.

Dimensions and configurations

8 listed configurations · view dimensions

Configuration | Outside diameter mm | Tooth width mm | Teeth options | Bore mm

Configuration	Outside diameter mm	Tooth width mm	Teeth options	Bore mm
1	130	1.4	40 or 60	25.4
2	160	1.4	60	25.4
3	180	1.4	60	25.4
4	180	1.6	40,60 or 80	25.4
5	200	1.6	40,60 or 80	25.4
6	230	1.7	40,60 or 80	25.4
7	254	2.1	40,60,80,100 or 120	25.4
8	300	2.3	40,60,80,100 or 120	30

Carbide-tip plastic and engineered-panel blades

Carbide-tip circular blades address selected medium/high-density engineered panels and plastic/wood machining. Match the actual panel structure, machine and required finish.

Geometry reference

Outside diameter 300 mm; tooth width 3.2 mm; bore 30 mm

Tooth directions

72 or 96 teeth

Construction direction

Relief-slot body; exact tooth profile and selected sample require approval

Diamond concrete-road cutting blades

Segmented diamond blades include different rim configurations and laser-welded directions for concrete-road cutting. Match the exact bore, segment geometry, cooling and marked limits to the road saw.

Dimensions and configurations

10 listed configurations · view dimensions

Configuration | Outside diameter mm | Bore mm | Segment height mm | Thickness mm | Segments/teeth | Construction direction

Configuration	Outside diameter mm	Bore mm	Segment height mm	Thickness mm	Segments/teeth	Construction direction
1	420	50	12	3.6	not tabulated	rim directionA
2	420	50	12	3.6	not tabulated	rim directionB
3	520	40	16	3.3	33	segmented directionC
4	420	40	16	3	27	segmented directionC
5	362	40	16	3	24	segmented directionC
6	420	40	16	3	27	segmented directionD
7	362	40	16	3	24	segmented directionD
8	500	38	19	3.5	36	laser-welded direction
9	400	38	19	3.2	28	laser-welded direction
10	350	38	19	3.2	24	laser-welded direction

Manual suction lifters for smooth panels

Aluminium-alloy bodies and natural-rubber cups combine lever-operated attachment and release. Single, twin and triple cups address manual handling of approved smooth, clean, nonporous glass, tile and panels. Match surface, holding orientation and handling conditions to an approved item and instructions.

Dimensions and configurations

5 listed configurations · view dimensions

Configuration | Cup configuration | Cup diameter mm | Listed horizontal load reference kg | Listed vertical load reference kg

Configuration	Cup configuration	Cup diameter mm	Listed horizontal load reference kg	Listed vertical load reference kg
1	single blue	123	50	35
2	twin blue	118	100	80
3	twin black	128	130	110
4	triple blue	118	120	100
5	triple black	128	150	130

Load qualification

Listed configuration references only; not a certified working-load limit or an overhead-lifting approval

Combined HSS drilling, tapping and chamfering tools

Ground 6542 HSS, a treated surface, double spiral flutes and a hexagonal holder combine pilot-hole, threading and chamfering operations on selected tapping equipment. Confirm the material, complete tool drawing and machine cycle.

Dimensions and configurations

6 listed configurations · view dimensions

Configuration | Thread | Drill-section length mm | Thread-section length mm | Overall length mm | Hex shank mm

Configuration	Thread	Drill-section length mm	Thread-section length mm	Overall length mm	Hex shank mm
1	M3×0.5	6.5	12.5	66.5	6.35
2	M4×0.7	6	11.5	66.5	6.35
3	M5×0.8	7	16	69.5	6.35
4	M6×1	6	17	68.5	6.35
5	M8×1.25	8.6	21	69.5	6.35
6	M10×1.5	11	22.5	71.5	6.35

Ground reduced-shank HSS drills

Fully-ground 9341 HSS drills combine a black appearance with a reduced round shank. Match the selected work material and chuck to the actual drawing.

Dimensions and configurations

8 listed configurations · view dimensions

Configuration | Diameter mm | Working length mm | Overall length mm | Shank mm

Configuration	Diameter mm	Working length mm	Overall length mm	Shank mm
1	13.5	107	159	12.5
2	14	109	159	12.5
3	14.5	112	167	12.5
4	15	113	168	12.5
5	15.5	117	177	12.5
6	16	118	178	12.5
7	18	128	188	12.5
8	20	138	202	12.5

Forged point, flat and wide demolition chisels

Forged, quenched spring-steel directions include square and hexagonal holders, point ends, flat edges and wide scraping edges. Provide the hammer holder and selected drawing; heavier hexagonal forms can also be discussed.

Dimensions and configurations

11 listed configurations · view dimensions

Configuration | Holder/profile | Body reference mm | Overall length mm | Working length mm | Edge width mm

Configuration	Holder/profile	Body reference mm	Overall length mm	Working length mm	Edge width mm
1	square flat	14	250	190	22
2	square flat	14	400	335	22
3	hex flat	17	280	230	22
4	hex flat	17	400	350	22
5	square point	14	250	186	point
6	square point	14	400	335	point
7	hex point	17	280	220	point
8	hex point	17	400	340	point
9	square wide	14	160	95	40
10	square wide	14	230	170	40
11	hex wide	17	370	320	50

Magnetic torsion-zone cross driver bits

D2-material driver bits combine a waisted torsion zone, magnetic cross tip and hexagonal holder. Discuss the screw profile and actual torque duty before sample approval.

Overall-length directions

50, 65, 75, 100 or 150 mm

Hex shank

6.35 mm

Diamond-grit multi-material cutting-disc direction

A diamond-grit edge, thick disc body and clearance ports provide a multi-material cutting-disc direction. Confirm the actual substrate and approved machine instructions for the selected item.

Geometry reference

Outside diameter 110 mm; bore 20 mm; thickness 1.8 mm

Long-series M35 cobalt-HSS twist drills

M35 cobalt-HSS and extended flutes provide a distinct long-reach drilling direction. Select material, fixture and usable reach with the approved drawing.

Dimensions and configurations

27 listed configurations · view dimensions

Configuration | Diameter mm | Overall length mm | Flute length mm

Configuration	Diameter mm	Overall length mm	Flute length mm
1	2	85	56
2	2.5	95	62
3	3	100	66
4	3.2	106	69
5	3.5	112	73
6	4	119	78
7	4.2	119	78
8	4.5	126	82
9	5	132	87
10	5.2	132	87
11	5.5	139	91
12	6	139	91
13	6.2	148	97
14	6.5	148	97
15	7	156	102
16	7.5	156	102
17	8	165	109
18	8.5	165	109
19	9	175	115
20	9.5	175	115
21	10	184	121
22	10.5	184	121
23	11	195	128
24	11.5	195	128
25	12	205	134
26	12.5	205	134
27	13	205	134